|
Features
Can be mixed and matched to create application-specific configurations
Ideal for general purpose switching of up
Can be used to switch a common point to either power or ground (Form C)
Connect together using external wiring for flexible switch design
Easy to use configuration software facilitates end-end path level switching for
simplified programming
|
|
EX1200-5001,-5002 Datasheet
EX1200-5001 : 80 Channel 2 Amp Form A (SPST) Switch
EX1200-5002 : 32 Channel 300 V/2 Amp SPDT switch
|
Overview
The EX1200-5001 and -5002 are high-density general purpose 2 A switch modules
designed for systems where individual relays can be used to route signals to/from the
units under test (UUT), or combined externally to form user-defined configurations.
These relays are commonly used to create complex signal distribution networks that
can be reconfigured through different wiring in test adapters. For example, three
relays on a -5002 module can be configured as a SP4T tree, and seven relays can
be configured as a SP8T tree. Up to 180 individual SPDT or 480 SPST relays can be
accommodated in a full rack mainframe for maximum density. The modules can also
be configured with other EX1200 series switch modules as part of a flexible system
switch design.
Since these modules may be used to switch power to the UUT or interface, the
digital input lines on the EX1200 series mainframes support the ability to force all
relays automatically to their normally open state if a fault condition occurs. This
approach instantly removes all power to the UUT or interface. These modules can
be automatically configured in the setup phase at the beginning of each scan step to
facilitate test sequencing and control.
|
|
Specifications
|
EX1200-5001
|
Channel Count
|
80 SPST (5001)
|
|
Maximum Switching Voltage
|
300 V AC, 300 V DC
|
|
Maximum Switching Current
|
2 A
|
|
Maximum Switching Power
|
60 W DC, 125 VA
|
|
Path Resistance
|
< 300 mΩ
|
|
Insulation Resistance
|
1x109 Ω
|
|
Maximum Thermal Offset
|
|
|
per Channel (HI-LO)
|
< 7 μV
|
|
Capacitance |
|
|
Open Channel |
< 50 pF |
|
Channel-Mainframe |
< 80 pF |
|
High-Low |
< 50 pF |
|
Bandwidth (-3 dB)
|
30 MHz (-5002), 10 MHz (-5001)
|
|
Crosstalk
|
|
|
100 kHz
|
< -80 dB
|
|
1 MHz
|
< -60 dB
|
|
Isolation
|
|
|
100 kHz
|
< -80 dB
|
|
1 MHz
|
< -45 dB
|
|
Rated Switch Operations
|
|
|
Mechanical
|
1x107
|
|
Electrical
|
5 x 105 at full load
|
|
Switching Time
|
< 3 ms
|
|
Connector Type
|
160p DIN (Form A Modules)
104p HD Dsub (Form C Modules)
|
|
|
Ordering Information
|
|
EX1200-5001 |
80 Channel 300 V/2 Amp SPDT switch |
|
EX1200-5002 |
32 Channel 300 V/2 Amp SPDT switch |
| EX1200-5006 |
40 Channel 300 V/2 Amp SPDT switch |
| EX1200-5007 |
12 Channel 300 V/2 Amp SPDT switch |
| 27-0389-104 |
104-pin HD D-sub mating connector with hood and pins, fixed contacts (no crimp tool required) |
| 27-0390-104 |
104-pin HD D-sub mating connector and backshell, solder cup style |
| 70-0297-001 |
Crimp tooling, includes handle and positioner, 22 AWG |
| 70-0363-501 |
104-pin HD D-sub mating connector and backshell, with 3 ft unterminated 22 AWG wire |
| 70-0367-003 |
EX1200-TB104SE, single-ended module for EX1200-5002 |
| 70-0367-005 |
EX1200-TB160SE, single-ended module for EX1200-5001 |
| 70-0363-504 |
Strain relief bracket kit (includes connector – recommended accessory) |
| 70-0363-503 |
Strain relief bracket kit (no connector) |
| 52-0109-000 |
Crimp pin (includes 100 crimp pins) |
| 46-0010-000 |
Crimp tool (DIN) |
| 46-0011-000 |
Extraction tool (DIN) |
| 27-0088-160 |
Mating connector |
|
|
|
